Setting Time and Date for the DS3231 RTC

From media_wiki
Revision as of 01:38, 29 July 2021 by U731219879 rc (talk | contribs)
Jump to: navigation, search
DS3231.PNG

Setting up the DS3231 RTC

 DS3231 RTC Datasheet: https://datasheets.maximintegrated.com/en/ds/DS3231.pdf
 Insert a coin cell battery into DS3231. 
 Either a CR2032 or LI2032 coin cell battery will work.
 Insert DS3231 module into the Power Logger PCB at J5. 

Download the Drivers

 The ds3231.h library can be downloaded from https://github.com/rodan/ds3231.
 Create a folder in Documents called Power-Fail-logger.
 Download and Save ds3231-master.zip to that folder.
 Install the Zip file by clicking on the Sketch Tab in the Arduino IDE. 
 Select Include library.   
 Select Add .ZIP Library...
 
 Ensure sure you have added these two libraries to the Arduino environment. 
Wire.h  
ds3231.h 
 

To Validate the libraries are installed

 Click the Sketch Tab
 Select Include library.
 The libraries will be listed 
 Arduino libraries      (Wire) 
 Contributed Libraries. (ds3231-master)

To Set the date and time use the follow program and paste in the Arduino IDE.


 // DS3231-Set-Time-Date.ino
 //This code can be found here:https://github.com/rodan/ds3231
 #include <Wire.h>    //Make sure you have added this library to the Arduino environment
 #include <ds3231.h>  //Make sure you have added this library to the Arduino environment
 struct ts t; 
 void setup() {
 Serial.begin(9600);
 Wire.begin();
 DS3231_init(DS3231_CONTROL_INTCN);
 /*----------------------------------------------------------------------------
 In order to synchronize your clock module, insert timetable values below !
 ----------------------------------------------------------------------------*/
 t.hour=20;      //Set the hour in military time to your current time. 
 t.min=40;       //Set the minutes. 
 t.sec=0;        //No need to change   
 t.mday=11;      //Set the Day
 t.mon=4;        //Set the Month
 t.year=2021;    //Set the Year
 DS3231_set(t);  //Comment this line out after setting RTC with time & date to validate
 }

 void loop() {
 DS3231_get(&t);
 Serial.print("Date : ");
 Serial.print(t.mon);
 Serial.print("/");
 Serial.print(t.mday);
 Serial.print("/");
 Serial.print(t.year);
 Serial.print("\t Hour : ");
 Serial.print(t.hour);
 Serial.print(":");
 Serial.println(t.min);
 Serial.print(":");
 Serial.println(t.sec);
 delay(60000);
 }
 void print2digits(int number){
 if (number >= 0 && number < 10) {
   Serial.write ('0');
 }
 Serial.print(number);
 } 

Set up Programmer

 Connect the USBTinyISP to the AVR-ISP-6 pin header J7 on the Power Fail Logger PCB.
 In the Arduino IDE click on Tools Tab - Select Programmer then select USBTinyISP.
Connect the Prolific USB-to-Serial Comm Port to the RS232 Port on the Power Fail Board Use Windows Device Manager to validate which Comm Port is used. In the Arduino IDE click on Tools Tab - Select Port then select the Prolific Port (Example Comm6).
Select correct target board In the Arduino IDE click on Tools Tab - Select Board then select the Arduino Uno.

Flash the Microcontroller with DS3231-Set-Time-Date Program

 Paste the above program DS3231-Set-Time-Date.ino into the Arduino IDE.
 After changing the time stamp in the program to match your current time do the following:
 In the Arduino IDE click on Sketch Tab - Select Upload Using Programmer
 

Validate the clock is set

 After program has uploaded go back and comment out the DS3231_set(t); statement. 
 Validate by reprograming the board with that line commented out.
 Use the same programming steps as stated above. 
In the Arduino IDE click on Tools Tab - Select Serial Monitor
Once the program has finished loading hit the Reset button on the Power Fail Logger Board. You should see the correct time and date display in the Serial Monitor. It will update and display the time once a minute

Next Step Flash the Microcontroller with Power-Fail-Logger Program

Power Fail Logger by Microrusty