Difference between revisions of "Main Page"
(19 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | |||
− | + | ==<strong>MicroRusty Embedded Workshop Wiki.</strong>== | |
− | == | + | [[File:Minion.jpg|left|thumb|upright=0.50]]<br> |
− | * [ | + | [http://merkle.hopto.org/cgi-bin/mcp9808.cgi Temperature in Jim's Den]<br><br><br> |
− | * [ | + | |
+ | Consult the [http://meta.wikimedia.org/wiki/Help:Contents User's Guide] for information on using the wiki software.<br> | ||
+ | ==[[ STM32 Workshops ]]== | ||
+ | ==[[ AVRDUDE Class]]== | ||
+ | ==[[ Raspberry Pi ]]== | ||
+ | ==[[ Future Classes ]]== | ||
+ | ==[[ November 2018 Workshop ]]== | ||
+ | {{Highlight |'''The design goals for this project is to make an inexpensive minimalist target board using an ATmega328P.'''|lightgreen}} | ||
+ | {{Highlight |'''Explain the processes used for programming the Micro-controller using the 6-pin ISP header using SPI interface.'''|lightgreen}} | ||
+ | |||
+ | How to use AVRdude to flash your program to the Micro-controller. | ||
+ | How to change the fuse settings (Clock speeds) 1MHz, 8MHz 16MHz. | ||
+ | How to use the AVR Inline assembly language in the Arduino IDE. How to use AVRdude int the terminal mode. | ||
+ | How to use the Arduino IDE to compile code and flash using the USB programmer through the ISP. | ||
+ | How to export the hex file and use it to program directly into Flash. How to read and write to EEPROM. | ||
+ | |||
+ | ==[[ KiCad 5.0 ]]== | ||
+ | |||
+ | {{Highlight |'''Design an RTC using the PCF85263AT/AJ'''|lightgreen}} | ||
+ | |||
+ | ==[[ PCF85263AT RTC by Microrusty ]]== | ||
+ | |||
+ | {{Highlight |'''How to use the PCF85263AT/AJ RTC''' |lightgreen}} | ||
+ | |||
+ | ==[[ Power Fail Logger by Microrusty ]]== | ||
+ | |||
+ | {{Highlight |'''Design a Power fail Logger using a RTC and SD Card ''' |lightgreen}} | ||
+ | |||
+ | |||
+ | * [//www.microrusty.com: Microrusty Main Page ] | ||
+ | * [//www.mediawiki.org/wiki/Manual:Configuration_settings Configuration settings list] | ||
+ | * [//www.mediawiki.org/wiki/Manual:FAQ MediaWiki FAQ] | ||
* [https://lists.wikimedia.org/mailman/listinfo/mediawiki-announce MediaWiki release mailing list] | * [https://lists.wikimedia.org/mailman/listinfo/mediawiki-announce MediaWiki release mailing list] | ||
− | * [ | + | * [//www.mediawiki.org/wiki/Localisation#Translation_resources Localise MediaWiki for your language] |
− |
Revision as of 02:31, 17 May 2021
Contents
MicroRusty Embedded Workshop Wiki.
Consult the User's Guide for information on using the wiki software.
STM32 Workshops
AVRDUDE Class
Raspberry Pi
Future Classes
November 2018 Workshop
The design goals for this project is to make an inexpensive minimalist target board using an ATmega328P. Explain the processes used for programming the Micro-controller using the 6-pin ISP header using SPI interface. How to use AVRdude to flash your program to the Micro-controller. How to change the fuse settings (Clock speeds) 1MHz, 8MHz 16MHz. How to use the AVR Inline assembly language in the Arduino IDE. How to use AVRdude int the terminal mode. How to use the Arduino IDE to compile code and flash using the USB programmer through the ISP. How to export the hex file and use it to program directly into Flash. How to read and write to EEPROM.
KiCad 5.0
Design an RTC using the PCF85263AT/AJ
PCF85263AT RTC by Microrusty
How to use the PCF85263AT/AJ RTC
Power Fail Logger by Microrusty
Design a Power fail Logger using a RTC and SD Card