Programming Power Fail Logger with Arduino IDE - Revision history

U731219879 rc at 21:46, 17 August 2021

2021-08-17T21:46:23Z

2021-08-17T21:41:43Z

2021-08-17T18:42:12Z

2021-08-17T18:38:39Z

2021-08-17T18:37:24Z

2021-07-30T21:39:04Z

2021-07-29T02:26:30Z

2021-07-29T02:24:34Z

2021-07-29T02:03:38Z

2021-05-25T22:58:52Z

@@ Line 174: / Line 174: @@
    Remove '''Jumper''' from '''J8'''
-'''Next Step:''' Installation and use <br>
+'''Next Step:''' Installation and use. Click on link below <br>
 ==[[ Power Fail Logger by Microrusty ]]==
 ==[[Initializing the Microcontroller]]==

@@ Line 174: / Line 174: @@
    Remove '''Jumper''' from '''J8'''
 ==[[Initializing the Microcontroller]]==
 ==[[Setting Time and Date for the DS3231 RTC]]==
 ----
-==[[ Power Fail Logger by Microrusty ]]==
+==[[ Main Page ]]==

@@ Line 173: / Line 173: @@
    Unplug '''USBTiny Programmer'''
    Remove '''Jumper''' from '''J8'''
-==[[Initializing the Microcontroller]]==
 ==[[Initializing the Microcontroller]]==
 ==[[Setting Time and Date for the DS3231 RTC]]==
 ----
 ==[[ Power Fail Logger by Microrusty ]]==

@@ Line 27: / Line 27: @@
    In the Arduino IDE click on '''Tools''' Tab - Select '''Board''' then select the '''Arduino Uno'''.<br>
 '''Validate the Arduino IDE has the following libraries installed before proceeding with the flash process.'''
-  #include <Wire.h>                   // For I2C Interface SDA SCK
+  #include <Wire.h>                   // For I2C Interface SDA SCK.
-  #include <ds3231.h>                 // For the DS3231 RTC library
+  #include <ds3231.h>                 // For the DS3231 RTC library.
-  #include <SPI.h>                    // SPI Interface that the SD card module will use
+  #include <SPI.h>                    // SPI Interface that the SD card module will use.
-  #include <SD.h>                     // for the SD card
+  #include <SD.h>                     // For the SD card.
 '''Flash the Microcontroller''' with '''Power-Fail-Logger''' Program

@@ Line 26: / Line 26: @@
    Select the correct target board.
    In the Arduino IDE click on '''Tools''' Tab - Select '''Board''' then select the '''Arduino Uno'''.<br>
 '''Flash the Microcontroller''' with '''Power-Fail-Logger''' Program

← Older revision		Revision as of 02:26, 29 July 2021
Line 170:		Line 170:
	Remove Jumper from J8		Remove Jumper from J8

−	==[[ ~~Power Fail Logger by Microrusty~~ ]]==	+	==[[Initializing the Microcontroller]]==

@@ Line 166: / Line 166: @@
    You should see the program running in the display of the Serial Monitor.
+  Unplug USBTiny Programmer
-Next Step '''Set up the SD Card reader'''
+  Unplug RS232 to USB Serial Interface
 ==[[ Power Fail Logger by Microrusty ]]==

@@ Line 30: / Line 30: @@
    Paste the program below '''Power-Fail-Logger Program.ino''' into the '''Arduino IDE'''.
    In the '''Arduino IDE''' click on '''Sketch''' Tab - Select '''Upload Using Programmer'''
+----
    /* Power_Fail_Logger.ino Jim Merkle and Rusty Cain
     *  Microrusty.com Copyright 4-12-2021
@@ Line 159: / Line 159: @@
    Serial.println("Data written:");
+   }
+----
 '''Validate the Power-Fail-Logger Program is running'''
    After program has uploaded   Validate