Power Fail Logger by Microrusty - Revision history

U731219879 rc at 21:51, 18 August 2021

2021-08-18T21:51:19Z

2021-08-18T21:49:21Z

2021-08-18T21:45:19Z

2021-08-18T21:44:47Z

2021-08-17T21:38:58Z

2021-08-17T21:05:46Z

2021-08-17T01:21:26Z

2021-08-17T01:12:30Z

2021-08-17T01:06:42Z

2021-08-17T00:53:00Z

@@ Line 7: / Line 7: @@
    The program only writes to the SD Card when there is a change in the AC Power Status from Power Good to Power Failure back to Power Good.
    To set the DS3231 RTC You must use another program called : DS3231-Set-Time-Date.ino See link below for How to set.
-   Serial Console Settings: Baud rate '''9600 8''' bit.
+   Serial Console Settings:  '''9600 Baud 8 bit.'''
 Program creates a file with the filename '''"REBOOTS.TXT"''' that captures each time the system is power cycled.
   Example of '''REBOOTS.TXT''' file:

@@ Line 1: / Line 1: @@
- '''www.Microrusty.com'''
+  '''Version 1.0 Copyright © Microrusty.com 2021  '''
 Latest Release : 04/12/2021 <br>
 Software written By '''Jim Merkle''' and '''Rusty Cain''' <br>
 Hardware design by '''Rusty Cain''' <br>
      '''Notes:'''
-   The program only writes to the SD Card when there is a change in the AC Power Status from Power Good to Power Failure to Power Good.
+   The program only writes to the SD Card when there is a change in the AC Power Status from Power Good to Power Failure back to Power Good.
    To set the DS3231 RTC You must use another program called : DS3231-Set-Time-Date.ino See link below for How to set.
    Serial Console Settings: Baud rate '''9600 8''' bit.
 Program creates a file with the filename '''"REBOOTS.TXT"''' that captures each time the system is power cycled.
   Example of '''REBOOTS.TXT''' file:

@@ Line 9: / Line 9: @@
    The program only writes to the SD Card when there is a change in the AC Power Status from Power Good to Power Failure to Power Good.
    To set the DS3231 RTC You must use another program called : DS3231-Set-Time-Date.ino See link below for How to set.
-   Serial Console Settings: Baud rate '''9600 8''' bit<br>
+   Serial Console Settings: Baud rate '''9600 8''' bit.
 Program creates a file with the filename '''"REBOOTS.TXT"''' that captures each time the system is power cycled.

@@ Line 10: / Line 10: @@
    To set the DS3231 RTC You must use another program called : DS3231-Set-Time-Date.ino See link below for How to set.
    Serial Console Settings: Baud rate '''9600 8''' bit<br>
-  Optimized for no power at the AC plug Automatic switching to battery on main power loss.
 Program creates a file with the filename '''"REBOOTS.TXT"''' that captures each time the system is power cycled.
   Example of '''REBOOTS.TXT''' file:

@@ Line 61: / Line 61: @@
 [[File:PowerLogger-Top.PNG |350px|left]]
 [[File:PowerLogger-Bottom.PNG|350px|mid]]
 ==[[Initializing the Microcontroller]]==
 ==[[Setting Time and Date for the DS3231 RTC]]==
 ==[[ Programming Power Fail Logger with Arduino IDE]]==
 ==[[Installation and use]]==
 ----
 ==[[ Main Page ]]==

@@ Line 56: / Line 56: @@
    #include <SPI.h>              // SPI Interface that the SD card module will use
    #include <SD.h>               // for the SD card
+ Download the libraries using the '''Arduino IDE''' refer to: '''Download the Drivers''' in '''Setting Time and Date for the DS3231 RTC'''
 [[File:PowerLogger-Top.PNG |350px|left]]

@@ Line 50: / Line 50: @@
    Three time log registers triggered from battery switch-over as well as input driven events.
    Featuring clock output and two independent interrupt signals.
-−
 [[File:PowerLogger-Top.PNG |350px|left]]

@@ Line 10: / Line 10: @@
    To set the DS3231 RTC You must use another program called : DS3231-Set-Time-Date.ino See link below for How to set.
    Serial Console Settings: Baud rate '''9600 8''' bit<br>
-   Optimized for no power at the AC plug
+   Optimized for no power at the AC plug Automatic switching to battery on main power loss.
 Program creates a file with the filename '''"REBOOTS.TXT"''' that captures each time the system is power cycled.
@@ Line 19: / Line 18: @@
    System Rebooted Date : 04/10/2021    Time : 20:24:53
-The program checks the '''RTC Board''' and '''SD Card reader''' to ensure both devices are working.
+The program checks the '''RTC Board''' and '''SD Card reader''' to ensure both devices are working. <br>
- Program sends device status to console port.
+Program sends '''SD Card reader''' status to console port.<br>
- Program sends power status to console port.
+Program sends '''power''' status to console port.
-Example :
+ '''Example :'''
    Initializing SD card...Setting up logging time
    Power Good
@@ Line 51: / Line 50: @@
    Three time log registers triggered from battery switch-over as well as input driven events.
    Featuring clock output and two independent interrupt signals.
-−
 [[File:PowerLogger-Top.PNG |350px|left]]